攀西钒钛磁铁矿尾矿制备储水泡沫陶瓷的研究

以攀西钒钛磁铁尾矿和废玻璃为主要原料通过高温烧结法制备储水泡沫陶瓷，研究原料配比和发泡剂（SiC）添加量对材料性能的影响。结果表明:随着钒钛磁铁矿尾矿含量的增加，材料的体积密度及抗压强度逐渐增大，平均气孔孔径逐渐减小；当尾矿添加量为50 wt%，材料的体积吸水率出现极值。当SiC添加量为0.3 wt%，材料内部气孔分布均匀，平均孔径约为2.93 mm。最终以50.0 wt%的钒钛磁铁矿尾矿和50.0 wt%的废玻璃为原料，外加3.0 wt%的石英，0.3 wt%的SiC，3.0 wt%的Na3PO4，在1040℃下制得性能最优的储水泡沫陶瓷，材料的体积密度为0.26 g/cm-3、体积吸水率为56.5%和抗压强度为0.68 MPa。采用SEM、XRD等检测手段研究材料的微观形貌及物相组成，结果表明储水泡沫陶瓷内部由三维立体结构组成，有利于储存水分；材料主要物相包括硅灰石、长石、透辉石和钛铁矿。      

基于DEM的振动筛筛孔形状对潮湿原煤筛分效果影响的研究

随着原煤含水量的增加,引起原煤颗粒间相互粘聚,影响振动筛筛分效率。基于离散元法,运用EDEM软件模拟了潮湿原煤颗粒在圆形筛孔、方形筛孔和矩形筛孔的筛分过程,并且以筛分效率和阻碍粒排出率为衡量指标,对振动筛筛孔形状影响潮湿煤筛分效果进行了研究。结果表明:在筛孔名义尺寸相同的情况下,潮湿煤在矩形筛孔筛面上的筛分效果最好,方形筛孔次之,圆形筛孔最差。     

In Silico Study on Tumor-Size-Dependent Thermal Profiles inside an Anthropomorphic Female Breast Phantom Subjected to Multi-Dipole Antenna Array

Electromagnetic hyperthermia as a potent adjuvant for conventional cancer therapies can be considered valuable in modern oncology, as its task is to thermally destroy cancer cells exposed to high-frequency electromagnetic fields. Hyperthermia treatment planning based on computer in silico simulations has the potential to improve the localized heating of breast tissues through the use of the phased-array dipole applicators. Herein, we intended to improve our understanding of temperature estimation in an anatomically accurate female breast phantom embedded with a tumor, particularly when it is exposed to an eight-element dipole antenna matrix surrounding the breast tissues. The Maxwell equations coupled with the modified Pennes’ bioheat equation was solved in the modelled breast tissues using the finite-difference time-domain (FDTD) engine. The microwave (MW) applicators around the object were modelled with shortened half-wavelength dipole antennas operating at the same 1 GHz frequency, but with different input power and phases for the dipole sources. The total input power of an eight-dipole antenna matrix was set at 8 W so that the temperature in the breast tumor did not exceed 42 °C. Finding the optimal setting for each dipole antenna from the matrix was our primary objective. Such a procedure should form the basis of any successful hyperthermia treatment planning. We applied the algorithm of multi for multi-objective optimization for the power and phases for the dipole sources in terms of maximizing the specific absorption rate (SAR) parameter inside the breast tumor while minimizing this parameter in the healthy tissues. Electro-thermal simulations were performed for tumors of different radii to confirm the reliable operation of the given optimization procedure. In the next step, thermal profiles for tumors of various sizes were calculated for the optimal parameters of dipole sources. The computed results showed that larger tumors heated better than smaller tumors; however, the procedure worked well regardless of the tumor size. This verifies the effectiveness of the applied optimization method, regardless of the various stages of breast tumor development.     

计及风险规避的电力零售商平衡市场交易模型

由于新能源出力以及终端负荷需求的不确定性,电力零售商在日前市场的竞标电量与实时市场的购买电量之间存在不平衡而产生惩罚成本风险。引入用户侧可控负荷作为平衡资源参与市场交易,提出了一种风险规避程度指标,以此来度量交易前后电量偏差程度,以信息熵度量残差序列离散程度计算风险规避程度指标。以电力零售商运行收益、用户需求响应满意度以及风险规避程度最大为目标建立多目标风险规避模型,采用自适应权重粒子群算法进行模型求解。通过算例表明,所提出的模型从电网-电力零售商-用户多个角度去考虑电力零售商参与平衡市场交易策略,能够有效提高电力零售商的运行效益以及用户满意度,同时可以提高电力市场管理的可靠性与安全性。     

直投式纳豆菌发酵剂制备工艺优化

为探索出一种工艺简便、成本低且活菌数高的直投式纳豆菌（Bacillus natto）发酵剂的制备方法，该研究以大米粉为基质替代传统的种子液培养基培养纳豆菌后直接将其烘干制成直投式纳豆菌发酵剂，通过单因素及正交试验优化直投式纳豆菌发酵剂的制备工艺。结果表明，用含1.5%蛋白胨的大米粉作为培养基，在接种量4.0%、加水量40%、培养温度43 ℃条件下培养纳豆菌28 h，菌体生长良好，将培养物烘干后制成的直投式纳豆菌发酵剂中的活菌数含量达4.71×109 CFU/g。此技术操作简便，可推广至工业生产中，简化生产过程。     

基于钠基吸附剂的烟气脱碳系统余热利用研究

针对基于钠基固体吸附剂的燃烧后脱碳技术应用于燃煤电厂后综合能耗偏高的问题，本文提出与供热机组结合的碳捕集/供热双机组系统，利用低温热网回水回收系统低品位余热。依据双机组的抽汽混合与否构建了两种系统流程，分析了两种不同方案下的系统性能。研究结果表明，在有效回收脱碳系统碳酸化反应余热后，独立抽汽方案中碳捕集综合能耗从4.05GJ/t CO₂降低至1.26GJ/t CO₂，而混合抽汽方案中碳捕集综合能耗降低至1.13GJ/t CO₂，同时双机组系统的热网供热量较单供热机组分别增加了67.5%和72.8%，经济效益显著。分析了混合抽汽方案的系统中碳捕集综合能耗随相关运行参数变化的规律，发现碳酸化反应温度和热网回水温度因为能够直接影响系统余热利用程度因而更易对碳捕集综合能耗产生影响。     

基于有限元的大流量换向阀仿真分析及结构优化

为了提高大流量换向阀的设计能力,该文采用ANSYS仿真平台对大流量换向阀仿真分析及结构优化。研究结果表明:撞击阶段应力集中区域基本出现在二级阀芯径向进油口部位,此时形成的最大应力等于24.26 MPa,明显比682 MPa的材料屈服极限更低。进液阀套达到了271.83 MPa的最大压应力,但明显低于682 MPa的屈服极限,表明壁厚满足设计标准。进液阀套形最大应力出现在阀套内部,跟瞬态冲击条件下最大应力出现区域存在明显差异。二级阀芯最大应力都出现于阀芯部位,完成结构优化之后,二级阀芯的最大应力发生了显著降低,其余各部位的应力也显著减小,可以满足设计标准。     

Damping and mode shape modification for additively manufactured walls with captured powder

This paper describes the fabrication, modeling, and dynamic testing of laser powder bed fusion stainless steel walls with captured powder cores. The purpose of the study is to determine the increased structural damping, or energy dissipation, and mode shape modification caused by the inclusion of the unmelted powder core within the solid walls. It is shown experimentally that the damping increases with larger powder core width and that the damping addition is mode dependent. Damping increases over the solid wall values by factors of 2.9–225 are reported depending on the mode number and core width. It is also seen that the mode shapes are distorted relative to the solid wall results as the core width is increased and wall thickness is decreased. Comparisons with finite element models confirm this trend.